Skill level: BEGINNERS


I’ve made up the flower as near to nature as possible, but used artistic licence so not botanically accurate.

I made three stamens (two joined with one behind it) . The petals sit as follows: Two tear drop petals either side of stamens, with a larger one at back of flower and a cupped one in the front.



You will need:
  • Saracino Flower Paste
  • Saracino Colour Dusts (purple, red, blue, white, yellow, green, brown)
  • Saracino Colour Paste (green, purple)
  • Florist Wires (30, 28, 22)
  • Florist Tape (Light Brown and White – ¼ inch)
  • Semolina
  • Edible Glue
  • Cornflour for dusting
  • Balling tool
  • Non stick rolling pin (I use 9”)
  • Cel Pad
  • Cel Board
  • Dresden tool or cutting wheel
  • Paint brushes (Flat for dusting (size 2 – 4 and one fine line brush [eg 000 size])
  • Small daisy cutter (I used tinkertech brand metal)
  • Wire Cutter
  • Kitchen Roll

Step 1

Roll out a small ball of premixed pink flower paste onto a 30 gauge wire

Step 2

Using a twisting movement downwards between fingers, spread the paste down the wire about a 1.5 centimeter with it thinner at top. Make two of those and one slightly longer. Curve slightly over finger and leave to dry. Stick the two shorter ones together and make sure the point meet at top.

Step 3

Tape the longer one over the back, with white tape

Step 4

Dust with a light dusting of purple and white mix dusts

Step 5

Mix semolina and yellow dust colour to make pollen. Dip the end of the double stamen into edible glue, then into pollen and leave to dry

Step 6

Back Petal:  Place a small ball of pale pink paste onto a 30 or 28 gauge wire. Roll paste between fingers to taper into a teardrop shape. Make as many as you require.

Step 7

Roll the tear drop out into a large petal on your board, and using small sharp scissors, cut a v shape at the top in the middle and using the ball tool on the centre of each side, at back of petal, to help it curve outwards

Step 8

Brush lightly with purple/white mix colour dusts.

Step 9

Tape to back of stamens

Step 10

Two side petals: Repeat same process at the back petal, but using a slightly smaller ball of paste onto a 28 or 30 gauge wire . Make 2 petals

Step 11

Using a ball tool, spread out to thin either side and upwards, keep the point at tip

Step 12

Dust very lightly with purple and white mix, keeping it slightly darker at base.

Step 13

Your petal should look like this.

Step 14

Tape, with white tape, to either side of stamens.

Step 15

Front petal:Same as before, roll out a ball of pink paste (about same size as back petal)  onto a 28 or 30 gauge wire

Step 16

Then ball out into a round cup shape, thinning the edges. Place ball of tool in centre to help it form cup shape.

Step 17

Dust lightly as previous petals.

Step 18

Take a very thin fine line brush and create a soft mottled effect, at base and centre of petal, with colour mixed with a little water

Step 19

Tape onto front of flower with cup facing upwards. Your flower is now complete

Step 20

Rosemary leaves – You will need to make a lot of these ( depending on how much you need to use). I used about 50-100 various sizes as you will see the rosemary sprig is varied.

Place a small ball of pale green paste onto a 30 gauge wire and taper between the fingers down the wire to form a long tear drop.

Step 21

Place onto your cel pad and gently press with your finger to flatten

Step 22

Form a middle vein by rolling up the centre, gently, with a cutting wheel. You could also use a dresden tool to do this.

Step 23

Dust with pale green first (I mixed a little green into yellow).

Step 24

Then colour dust with a darker green (I mix a little brown and blue into the green) keep it lighter at the tips and no need to dust the back as leaves are lighter at the back.

Step 25

WIth the fineliner brush with a little white that’s been mixed with a little water, paint a line down the centre. I put some onto the edges as well, just here and there

Step 26

Make a lot of leaves, all different sizes.

Step 27

Group leaves with brown tape.

Step 28

Leaves should be grouped in various sizes and numbers

Step 29

Start with a small sprig of leaves at top of taped full wire, then work your way down the wire with single as well as groups of leaves

Step 30

Add the occasional blossom as you go down.

Step 31

Tape a few short branches to main one.

Step 33

Here is completed rosemary sprig with blossoms

Subscribe To Our Newsletter

Subscribe To Our Newsletter

We'd love to send you the latest news, discounts & exclusive offers via email! By signing up below you are confirming you are happy for Saracino to send you marketing emails. We will always treat your personal details with the upmost respect & will never sell your details to other companies for marketing purposes.

Privacy Policy | GDPR

You have Successfully Subscribed!